Uprava sluchatok + obrazky

[KeNnY]

takze davam tu navod na upravu sluchatok pre K750i  .. zatial v ang 

Well, got my spankin new K750i yesterday, and after less than 24h i decided to put my soldering iron into it!
Well, not the phone itself, but the headset.
After modding my Qtek S100 headset a while back (S100 traded against K750, can't say I miss it really...) and using it as an MP3-player with 1GB SD in it, I decided that I want to go and use the K750 as one too, but the standard headset didn't really give me what I wanted.
The procedure is pretty simple: (and of course, all pics are taken with, you guessed it, a K750i! )
#1. Take a sharp knive. Gently try to wiggle it in where the red frame is. Jerk gently and the cover will come into two pieces.
#2. This is what you will see next.
#3. Closeup. You might notice a black cable on the upper right corner by the PCB that looks like something that has come off. It isn't. The + cable going from the phone out to the left earpiece never touches the PCB. They are wrapped together and covered with this "shrinking wire" (or whetever you call it in english).
After coming to this, I decided to take off the right earpiece first since it was only 2 soldered spots that needed to be removed. Then you want to remove those grey rubberpieces that sit on the cable, and put them on your new earpice. It will take some tinkering, but it's not that difficult. All you need is patience, especially when putting it on the new cable.
#4. One earpiece soldered in place. Testrun to see that everything works. Wow, what a difference!
#5. Closeup.
#6. Well, after quite a bit of tinkering, this is how it will end up. What you do is: Unsolder the bottom right cable (on pic. with and "S" above it). Take apart those two that were wrapped together (ex. remove the rubber shielding and cut the one that goes to the earpice). Then you put in the cable to the new earpiece, wrap + to + and shrink them together, wrap - to the "S" cable (on pic.) and solder them to the PCB.
Testrun, and enjoy the new and improved headset!
(And the headset doesn't need to be a Koss The Plug, you may use whatever you like. It's up to you and your personal preferences.)
Hope someone finds this useful, and can deal with my lousy descriptions and pics (quite tired right now...).
Cheers!
Edit: What is the best way to post pics here? Since attachments wont swallow anything...
Edit 2: Well, here are the pics:
http://home.aland.net/m02454/hemsidor/bilder/headset/DSC00051.jpg
http://home.aland.net/m02454/hemsidor/bilder/headset/DSC00046.jpg
http://home.aland.net/m02454/hemsidor/bilder/headset/DSC00047.jpg
http://home.aland.net/m02454/hemsidor/bilder/headset/DSC00048.jpg
http://home.aland.net/m02454/hemsidor/bilder/headset/DSC00049.jpg
http://home.aland.net/m02454/hemsidor/bilder/headset/DSC00050.jpg


original zkopirovany z http://www.howardforums.com/showthread.php?t=644684

 

[gomeZZZ]

oh boze.......
tak dotoho nejdu....az pujdes na sraz Kenny,tak si vem pajku,zrobis mi to ty,ja bych dotoho nevrtal

[sarhzajda]

takze davam tu navod na upravu sluchatok pre K750i   .. zatial v ang  

Well, got my spankin new K750i yesterday, and after less than 24h i decided to put my soldering iron into it!
Well, not the phone itself, but the headset.
After modding my Qtek S100 headset a while back (S100 traded against K750, can't say I miss it really...) and using it as an MP3-player with 1GB SD in it, I decided that I want to go and use the K750 as one too, but the standard headset didn't really give me what I wanted.
The procedure is pretty simple: (and of course, all pics are taken with, you guessed it, a K750i! )
#1. Take a sharp knive. Gently try to wiggle it in where the red frame is. Jerk gently and the cover will come into two pieces.
#2. This is what you will see next.
#3. Closeup. You might notice a black cable on the upper right corner by the PCB that looks like something that has come off. It isn't. The + cable going from the phone out to the left earpiece never touches the PCB. They are wrapped together and covered with this "shrinking wire" (or whetever you call it in english).
After coming to this, I decided to take off the right earpiece first since it was only 2 soldered spots that needed to be removed. Then you want to remove those grey rubberpieces that sit on the cable, and put them on your new earpice. It will take some tinkering, but it's not that difficult. All you need is patience, especially when putting it on the new cable.
#4. One earpiece soldered in place. Testrun to see that everything works. Wow, what a difference!
#5. Closeup.
#6. Well, after quite a bit of tinkering, this is how it will end up. What you do is: Unsolder the bottom right cable (on pic. with and "S" above it). Take apart those two that were wrapped together (ex. remove the rubber shielding and cut the one that goes to the earpice). Then you put in the cable to the new earpiece, wrap + to + and shrink them together, wrap - to the "S" cable (on pic.) and solder them to the PCB.
Testrun, and enjoy the new and improved headset!
(And the headset doesn't need to be a Koss The Plug, you may use whatever you like. It's up to you and your personal preferences.)
Hope someone finds this useful, and can deal with my lousy descriptions and pics (quite tired right now...).
Cheers!
Edit: What is the best way to post pics here? Since attachments wont swallow anything...
Edit 2: Well, here are the pics:
http://home.aland.net/m02454/hemsidor/bilder/headset/DSC00051.jpg
http://home.aland.net/m02454/hemsidor/bilder/headset/DSC00046.jpg
http://home.aland.net/m02454/hemsidor/bilder/headset/DSC00047.jpg
http://home.aland.net/m02454/hemsidor/bilder/headset/DSC00048.jpg
http://home.aland.net/m02454/hemsidor/bilder/headset/DSC00049.jpg
http://home.aland.net/m02454/hemsidor/bilder/headset/DSC00050.jpg


original zkopirovany z http://www.howardforums.com/showthread.php?t=644684

 

Ty tak budes pitvat ta sluchatka??? Jsi blazen a nebo neuveritelne zrucny...

[olas11]

to neni vubec slozite...mozna to vypada, ale neni

[Vita]

presne tak, taky se to chystam udelat jen kdyby jsi prosimte prelozil ten navod urcite tam nebude nic duleziteho ale pro jistotu diky 

[gomeZZZ]

presne tak, taky se to chystam udelat jen kdyby jsi prosimte prelozil ten navod urcite tam nebude nic duleziteho ale pro jistotu diky  

pc translator to zmaknul takto:
Dobre, dostal muj vyprask novy K750i vcera, a po mene nez 24h i jsem rozhodl se dat mou pajecku do toho!
Dobre, ne telefon sam, ale sluchatko s mikrofonem.
Po hypermodernim mem Qtek S100 sluchatku s mikrofonem pred chvili (S100 obchodni proti K750, nemoct rict, ze ja minu to opravdu...) a pouzivani to tak MP3 prehravac s 1GB SD v tom, ja jsem rozhodl, ze ja chci jit a uzivat K750 jak jeden take, ale standardni sluchatko s mikrofonem ne opravdu dat mi co chtel jsem.
Procedura je docela jednoducha: (a samozrejme, vsechny obrazky jsou okouzlene, vy jste hadali to, K750i! )
#1. Vezmete ostry riznete. Jemne zkuste trast se to v kde cerveny ram je. Trhnout jemne a kryt vstoupi do dvou kusu.
#2. Toto je co vy budete videt dalsi.
#3. Detail. Mozna, ze bys mohl vsimnout si cerneho kabelu na pravem hornim rohu PCB ktery vypada jako neco, co utrhl se. To neni. + kabel jdouci z telefonu ven vlevo ochranna klapka na usi nikdy dotyka se PCB. Oni jsou zabaleni spolecne a pokryty timto "bazlivym dratem" (nebo brousit-vubec kdy vy nazyvate to v anglictine).
Po prichazejici k tomu, ja jsem rozhodl se vzletnout pravou ochrannou klapku na usi prvni protoze to je jen 2 pajenych bodu ktere potrebovaly byt odstranene. Pak vy chcete odstranit ty sede kaucukove - kusy ktere sedi na kabelu, a dat je na vase nove earpice. To vezme nejaky fusujici, ale to neni tomu obtizne. Vse co potrebujete je trpelivost, zvlasÂť kdyz davani to na novem kabelu.
#4. Jedna ochranna klapka na usi pajene na miste. Testrun videt ze vsechno pracuje. Pani !, jaky rozdil!
#5. Detail.
#6. Dobre, po docela kusu fusujici, toto je jak to skonci. Co vy jste: Rozletujte spodni pravy kabel (na fotce. s a "S" nad to). Rozeberte ti dva ktery jste byli zabaleni spolecne (ex -. odstranit kaucukove stineni a rezete ten, ktere jde do earpice). Pak vy date dovnitr telegramu nove ochranne klapce na usi, obal + + a srazi se jim spolecne, obal - "S" kabel (na fotce.) a paji je k PCB.
Testrun, a tesi se z noveho a zlepseneho sluchatka s mikrofonem!
(a sluchatko s mikrofonem nemusi byt Koss zasuvka, muzete pouzijete cokoliv vy mate rad. To zalezi na tobe a vase osobni predvolby.)
Nadeje nekdo naleza toto uzitecny, a muze jednat s mymi hnusnymi popisy a obrazky (docela unaveny prave ted...) .
Na zdravi!
Uprava: Jaky je nejlepsi zpusob jak poslat obrazky zde? Od naklonnosti zvykla vlastovka cokoli...
Editovat 2: Dobre, zde jsou obrazky:

[KeNnY]

tak tenhle preklad jsem nepochopil vubec 

ale nieje to tak zlozite... otvoris, odpajkujes, zalozis, zapajkujes, otestujes  a je to... ale ja si myslim ze tie sluchatka budu stacit... toto je len pre tych ktory su MOC narocny na hudbu ... on si tam daval tieto sluchatka ja by som si tam pripajkoval sluchatka tiez koss ale ine (viz obrazok) alebo tieto ...

ale este uvidim 

[xtj]

to ja bych si tam spis pridelal 3,5mm vstupni jack .. abych mohl pripojit jakykoli sluchatka ...ale uvidim jestli seberu odvahu ty sluchatka rozebrat ...

[Vita]

Mam napad 
Urcite jste videli kabel ktery ma z mobilu vyvod na cinch k tomu dokoupite dalsi kabel, ktery bude na jedne strane cinch a na druhe jack 3,5 pak uz si tam jen date sluchatka jake chcete
Bude to sice dlouhe jako krava ale pofarato bez jakeho koliv zasahu

[KeNnY]

mam este lepsi sposob ako upravit sluchatka!


na toto musim povedat bravo! 

http://mobile-review.com/forum2/showthread.php?t=29441

[milda2000]

Mam napad  
Urcite jste videli kabel ktery ma z mobilu vyvod na cinch k tomu dokoupite dalsi kabel, ktery bude na jedne strane cinch a na druhe jack 3,5 pak uz si tam jen date sluchatka jake chcete
Bude to sice dlouhe jako krava ale pofarato bez jakeho koliv zasahu

Co nevidet bude v prodeji redukce s bocnim vyvodem jack 3,5, W800 ho bude mit standartne v baleni.

Milda

[vita]

JJ mas to moc pekny nevim proc me to  nenapadlo ale kdyby se to napojilo na ten cinch tak by se tomu nic nestalo no at si kazdy udela jak chce. Ja stejne beru to tvoje mas to super  

[Vita]

To milda docela by me zajimalo odkud mas tyto informace diky 

[KeNnY]

2 YAMATO:
tady to mas!

[YAMATO]

Budu urcite vypadat jako nevdecnik, ale to neni ono ...ja si predstavuju Fast Port, cca 10 cm kabelu a 3,5 mm jack. A aby nefungobvalo HF, pokud to jde. Ja HF naprosto nesnasim (no jo, jsem blazen ) a taky nechci byt omotany kabely. A hlavne...jak se to zapoji v tom jacku?